Mr-gasket 7667 Floor Shifter Conversion: 3-Speed User Manual download pdf

UNIVERSAL FLOOR SHIFT

CONVERSION KIT

#7666 & #7667

These instructions apply to the following MR. GASKET products:

INSTALLATION INSTRUCTIONS

WORK SAFELY

Perform this installation on a good, clean, level surface for

maximum safety and with the engine turned “OFF”.

Installation of this shifter requires working underneath the

vehicle. Raise vehicle by lifting at points specified by the

vehicle manufacturer. Place blocks or wedges in front of and

behind both rear wheels to prevent movement in either

direction. Support the vehicle with approved automotive

support stands or wheel ramps.

DO NOT USE A BUMPER JACK FOR SUPPORTING VEHICLE.

USE EXTREME CARE AND CAUTION WHEN WORKING

UNDERNEATH VEHICLE.

Never get near or under vehicle until you are confident that

it is safely supported and will not move or fall from its

raised position.

The following parts are included in this package:

7666 7667

Qty. Part No. Part No. Description

1 97091037 9709137 Knob

1 501 0004 501 0025 Shifter Assembly

1 117 0001 117 0001 Bracket - Mounting

1 116 0001Z 116 0001Z Brace - Stiffener

1 247 0005Z 247 0005Z Support - Lower Mounting

1 247 0008Z 247 0008Z Support - Extension (Optional Use)

1 247 0007Z 247 0007Z Support - Upper (Optional Use)

1 247 0006Z 247 0006Z Support - Lower (Optional Use)

2 105 0005Z 105 0005Z Transmission Arm - For Milled Shafts

2 105 0004Z 105 0004Z Transmission Arm - For Round Shafts

1 213 0002Z 213 0190Z Linkage Rod

1 213 0003Z 213 0192Z Linkage Rod

1 179 8805 179 8805 Jam Nut

1 154 0002 154 0176 Bagged Hardware

2 119 8057PO 119 8057PO Rod Adjusting Button

1–425 0005PO Coupling-Rod Extension

1–213 0209Z Rod-Threaded

2 97X91028 97X91028 “U” Bolt

2 97090030 97090030 7/16-14 x 1 Hex Head Bolt

1 97090031 97090031 7/16-14 x 1-1/4 Hex Head Bolt

5 97000686 97000686 1/2" Flatwasher

3 97000404 97000404 7/16" Lockwasher

2 179 4343 179 4343 7/16-14 Hex Nut

3 97001805 97001805 5/16-24 x 1 Hex Head Bolt

3 96000559 96000559 5/16" Flatwasher

7 97000088 97000088 5/16-24 Hex Nut

7 97000089 97000089 5/16" Lockwasher

4 97000015 97000015 Spring Clip

4 97090079 97090079 #10-12 x 1 Pan Head Screw

1 114 8058 114 8058 Rubber Boot

1 195 2590 195 2590 Trim Plate

1 1540110 1540110 Hardware Kit

1 1010010 1010010 Ignition Block Adapter

1 1120007 1120007 Ignition Block

1 2280062 2280062 Spacer

2 2720008 2720008 Screw, 6-32 x 7/16

2 2720009 2720009 Screw, 6-32 x 5/8

SHIFTER INSTALLATION

1. Place factory shifter in NEUTRAL position. Disconnect and

remove stock linkage. Remove stock column shift lever by

driving pin out.

STEERING COLUMN LOCK-BACKDRIVE LINKAGE

MODIFICATION FOR 1969 & LATER VEHICLES.

Steering column lock activated by the shifting linkage must

be modified as follows: Secure the 1st/REVERSE lever

(located at the front of steering column, ahead of firewall in

engine compartment,) in its REVERSE position so it cannot

move. This will allow column to “LOCK” when the ignition

key is turned to the “OFF” position and withdraw freely out

of lock.

The SAFETY IGNITION BLOCK device supplied with this kit

MUST be installed as shown on page 4.

2. Remove Mr. Gasket shifter from mounting bracket. Be

careful when removing, as internal components of shifter

mechanism will become loose and may separate from

housing. Install bracket to transmission as shown.

NOTE: Three basic brackets (items 3, 4 & 5) are used in all

installations to mount the shifter. You may have to bend

or trim some of the brackets for clearance purposes and

to help ease assembly. Three optional pieces (items 6, 7 &

8) are used when it is necessary to clear obstructions on

trans-mission extension housing. Assemble using 5/16-24

X 1” hex head bolts, lockwashers and hex nuts supplied.

REFER TO FIG. 1.

Vehicles equipped with an Overdrive Transmission have

a cross-member support located underneath the floor-

board, this may interfere with the shifter installation. Cut

a section of the cross-member support out of floorboard

or trim the shifter mounting bracket for clearance.

Overdrive Transmission installations may require using

optional support pieces (items 6, 7 & 8).

7666 7667

Qty. Part No. Part No. Description

7666 - Universal Floor Shift Conversion Kit, Fits Most

Rear-Wheel Drive Passenger Car Applications

With 3-Speed Manual Transmissions

7667 - Universal Floor Shift Conversion Kit, Fits Most

Pick-Up Truck Applications With 3-Speed Manual

Transmissions

1 2 3 4

Summary of Contents

Page 1 - CONVERSION KIT

UNIVERSAL FLOOR SHIFTCONVERSION KIT#7666 & #7667These instructions apply to the following MR. GASKET products:INSTALLATION INSTRUCTIONSWORK SAFELY

Page 2

NOTE: 1/2” diameter flatwashers are supplied to be used asspacers between the mounting brackets and transmissionflange. Longer length 7/16” diameter b

Page 3 - CAR INSTALLATION

TRUCK INSTALLATIONFIG. 4FIG. 5USE THE SLOTS THAT LOCATE ARMS INTHE BEST POSITION.ARMS FOR MILLEDCONTROL SHAFTSARMS FOR ROUNDCONTROL SHAFTSFILEDSLO

Page 4 - SAFETY IGNITION BLOCK

INSTALLATION & OPERATING INSTRUCTIONSSAFETY IGNITION BLOCKThis is a positive device that assures that manipulation ofthe ignition key switch to th

Comments to this Manuals

No comments

Mr-gasket 7667 Floor Shifter Conversion: 3-Speed User Manual

Browse online or download User Manual for For the car Mr-gasket 7667 Floor Shifter Conversion: 3-Speed. Mr. Gasket 7667 Floor Shifter Conversion: 3-Speed User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Mr-gasket 7667 Floor Shifter Conversion: 3-Speed