Mr-gasket 7668 Floor Shifter Conversion: 3-4 Speed Auto User Manual download pdf

UNIVERSAL FLOOR SHIFT

CONVERSION KIT

#7668

These instructions apply to the following MR. GASKET products:

7668 - Universal Floor Shift Conversion Kit, Fits Most Rear-Wheel Drive Car Applications

With Automatic Transmissions

INSTALLATION INSTRUCTIONS

WORK SAFELY

Perform this installation on a good, clean, level surface for

maximum safety and with the engine turned “OFF”.

Installation of this shifter requires working underneath the

vehicle. Raise vehicle by lifting at points specified by the

vehicle manufacturer. Place blocks or wedges in front of and

behind both rear wheels to prevent movement in either

direction. Support the vehicle with approved automotive

support stands or wheel ramps.

DO NOT USE A BUMPER JACK FOR SUPPORTING VEHICLE.

USE EXTREME CARE AND CAUTION WHEN WORKING

UNDERNEATH VEHICLE.

Never get near or under vehicle until you are confident that

it is safely supported and will not move or fall from its

raised position.

The following parts are included in this package:

Qty. Part No. Description

1 95090704 Shifter Assembly

1 97091050 Knob

1114 8058 Rubber Boot

1195 2590 Trim Plate

1216 0001 Weather-Seal (Plastic Sheet)

1170 0008Z Lever-Extender for Shifter

1119 3783PO Rod Adjusting Button

2 97000015 Spring Clip

1190 0001 3/32" x 3/4" Cotter Pin

1213 0011 Z Connecting Rod - Straight

1213 0012Z Connecting Rod - Bent

1195 0132Z Special Adapter

1105 0007Z Transmission Arm/Adapter

1105 0008Z Transmission Arm/Adapter

1105 0009Z Transmission Arm/Adapter

1105 0011Z Transmission Arm/Adapter

1105 0012Z Transmission Arm/Adapter

2 265 0001 “U” Bolt – 1/4-20 Thread

1 265 0002 “U” Bolt – 1/4-28 Thread

6 97080969 1/4-20 x 1" Hex Head Cap Screw

1215 0004 1/4-20 x 1-3/4" Head Cap Screw

10 97090082 1/4" Split Lockwasher

10 97000740 1/4-20 Hex Nut

4 267 3534 1/4" Flatwasher (5/64" Thick)

1 97090729 1/4" Flatwasher (1/16" Thick)

1 97090096 5/16-18 x 1" Hex Head Cap Screw

1 97000089 5/16" Split Lockwasher

1 97000670 5/16-18 Hex Nut

2 97000661 3/8-24 Hex Nut

1 97090062 3/8-24 Hex Jam Nut

1 97090058 3/8" Flatwasher

4 97090079 #10-12 x 1 Sheet Metal Screw

11540110 Hardware Kit

1 1010010 Ignition Block Adapter

11120007 Ignition Block

1 2280062 Spacer

2 2720008 Screw, 6-32 x 7/16

2 2720009 Screw, 6-32 x 5/8

SHIFTER INSTALLATION

1. Turn ignition key forward to unlock position on steering

column, if equipped, and place factory shifter in NEUTRAL

position.

Column shift applications: Remove drive pin that fastens

factory shifter lever to steering column, then remove lever

from column. Disconnect and remove shifter rod from

transmission. Do not remove rod to throttle.

Factory floor shift (console mount) applications:

Disconnect and remove console, shifter assembly, cable,

brackets and transmission arm if necessary. Do not

remove rod to throttle.

STEERING COLUMN LOCK-FOR 1969 & LATER VEHICLES

The SAFETY IGNITION BLOCK device supplied with this kit

MUST be installed as shown on page 6. It must be installed

to prevent the possibility of turning the ignition switch off

while vehicle is in motion. The steering column will lock

when this switch is turned off. Failure to heed this warning

could result in accidental steering lock-up while vehicle is in

motion.

2. Select a position for the shifter assembly on the center

line of floor tunnel. Punch or drill a small hole through

floor tunnel to mark location.

3. Check location underneath vehicle to be sure that shifter

will clear transmission rear support. Place template

supplied with this kit on the carpet. Locate “X” on

template over punched mark.

Trace outline of opening to be cut out on the carpet, then

carefully cut and remove carpet. Trace the outline of area

Qty. Part No. Description

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - CONVERSION KIT

UNIVERSAL FLOOR SHIFTCONVERSION KIT#7668These instructions apply to the following MR. GASKET products:7668 - Universal Floor Shift Conversion Kit, Fit

Page 2 - GM 1965-1968

to be removed from floor tunnel. Check area under floortunnel for obstructions before drilling. Drill a series ofstarter holes through floor tunnel an

Page 3

1954-1955 CHEVROLETPIVOTSHAFTSTOCKLINK“U” BOLTKITROD105 0007ZTRANS ARM/ADAPTERSTOCKSELECTORARM1964-1965 CHEVROLET5/16” BOLTAND NUT105 0012ZTRANS ARM/A

Page 4

1960 CHEVROLETKIT RODSTOCK SELECTORARM105 0012ZTRANS ARM/ADAPTER“U” BOLTBUICKSSTOCKSELECTORARM“U” BOLTNUTSKITROD105 0012ZTRANS ARM/ADAPTERSPRINGCLIP19

Page 5

IDENTIFICATION OF TRANSMISSION ARMS/ADAPTERSIMPORTANT!After installation iscomplete, be sure toadjust the pivot bolttension, #26. The shifteris adjust

Page 6

TEMPLATE FOR CUTTING OPENINGS IN CARPETAND FLOOR TUNNEL & DRILLING HOLESHEAVY OUTLINEINDICATES OPENING THAT ISTO BE CUT IN THEFLOOR TUNNELDRILLFO

Page 7 - SAFETY IGNITION BLOCK

INSTALLATION & OPERATING INSTRUCTIONSSAFETY IGNITION BLOCKThis is a positive device that assures that manipulation ofthe ignition key switch to th

Page 8

Comments to this Manuals

No comments

Mr-gasket 7668 Floor Shifter Conversion: 3-4 Speed Auto User Manual

Browse online or download User Manual for For the car Mr-gasket 7668 Floor Shifter Conversion: 3-4 Speed Auto. Mr. Gasket 7668 Floor Shifter Conversion: 3-4 Speed Auto User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Mr-gasket 7668 Floor Shifter Conversion: 3-4 Speed Auto